Gw-instek PEL-3000 Series Programming Manual Uživatelský manuál Strana 29
- Strana / 174
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
COMMNAND OVERVIEW
27
Common Commands
*CLS ....................................................................................... 27
*ESE ....................................................................................... 27
*ESR? ..................................................................................... 28
*IDN? ..................................................................................... 28
*OPC ...................................................................................... 29
*RCL ....................................................................................... 29
*RST ....................................................................................... 29
*SAV ....................................................................................... 30
*SRE ....................................................................................... 30
*STB? ..................................................................................... 31
*TRG ...................................................................................... 31
*TST? ..................................................................................... 32
*WAI ...................................................................................... 32
*CLS
Set
Description
Clears the error queue.
Syntax
*CLS
*ESE
Set
Query
Description
Queries or sets the Standard Event Status Enable
register. The Standard Event Status Enable register
determines which events can set the Event
Summary bit (ESB) in the Status Byte Register. Any
bits that are set to 1 enable the corresponding
event. Each event is represented by a bit in the
Standard Event Status Enable register.
Syntax
*ESE <NR1>
Query Syntax
*ESE?
Parameter/
Return parameter
<NR1> (bit weight)
Bit number / Description
1
0/ OPC
4
2/ QYE
8
3/ DDE
- DC Electronic Load 1
- Table of Contents 3
- INTERFACE OVERVIEW 4
- Front Panel Overview 5
- Rear Panel Overview 6
- Interface Configuration 7
- Configure GPIB Interface 8
- 1 2 3 4 5 9
- GPIB Function Check 15
- INTERFACE OVERVIEW 17
- COMMNAND OVERVIEW 18
- :CURRent:Set 21
- Command List 23
- :CURRent[:VA]:TRIGgered 37
- :RESistance[:VA]:TRIGgered 37
- Example 38
- :RESistance:TRIGgered MAX 38
- :INPut:MODE 40
- :MEASure:ETIMe? 42
- Configure Subsystem Commands 43
- [:CONFigure]:OCP 43
- [:CONFigure]:OPP 44
- [:CONFigure]:SSTart 46
- [:CONFigure]:COTime 49
- [:CONFigure]:GNG:C 55
- Parallel Commands 56
- [:CONFigure]:PARallel 56
- Step Resolution Commands 58
- [:CONFigure]:STEP:CCH 58
- [:CONFigure]:STEP:CC 60
- [:CONFigure]:STEP:CRH 60
- [:CONFigure]:STEP:CRM 61
- [:CONFigure]:STEP:CRL 62
- [:CONFigure]:STEP:CR 62
- [:CONFigure]:STEP:CV 64
- [:CONFigure]:STEP:CPH 64
- [:CONFigure]:STEP:CP 66
- [:MODE]:DYNamic 71
- Current Subsystem Commands 72
- :CURRent[:VA] 72
- :CURRent:SET 75
- :CURRent:T2 78
- :RESistance[:VA] 81
- :RESistance:L1 83
- :RESistance:LEVel 85
- :RESistance:T1 87
- :RESistance:DUTY 89
- Power Subsystem Commands 93
- :POWer[:VA] 93
- :POWer:LEVel 96
- :POWer:FREQuency 98
- :POWer:DUTY 99
- Function Commands 100
- :PROGram:STATe 101
- :PROGram 102
- :PROGram[:RECall]:DEFault 103
- :PROGram:STARt 103
- [:PROGram]:CHAin:P2P 109
- :PROGram:SAVE 110
- :NSEQuence:STATe 110
- :NSEQuence 111
- :NSEQuence:STARt 112
- :NSEQuence:EDIT 117
- :NSEQuence:EDIT:POINt 118
- :FSEQuence 120
- :FSEQuence:MEMO 121
- :FSEQuence:EDIT:POINt 126
- :FSEQuence:SAVE 128
- :UTILity:LOAD:MODE 130
- :UTILity:LOAD:RANGe 131
- SCPI Register Commands 142
- :SYSTem:ERRor? 142
- :STATus:PRESet 143
- :STATus:CSUMmary:PTRansition 151
- Status Registers 153
- CSummary Status Registers 155
- Questionable Status Register 156
- Operation Status Registers 157
- Status Byte Register 160
- Service Request Register 161
- Error Messages 162
Související produkty a manuály pro Zařízení Gw-instek PEL-3000 Series Programming Manual
Zařízení Gw-instek PCS-1000 Uživatelský manuál
(93 stránky)
(93 stránky)
Zařízení Gw-instek GPD-4303S Uživatelský manuál
(59 stránky)
(59 stránky)
Zařízení Gw-instek PPH-1503 Uživatelský manuál
(137 stránky)
(137 stránky)
Zařízení Gw-instek LCR-914 Uživatelský manuál
(28 stránky)
(28 stránky)
Zařízení Gw-instek LCR-800 Series Uživatelský manuál
(72 stránky)
(72 stránky)
Zařízení Gw-instek GPM-8212 Uživatelský manuál
(14 stránky)
(14 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce