Gw-instek GOM-802 Programming Manual Uživatelský manuál Strana 1

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ ⎯1CONTENTS PAGE1. INTRODUCTION...1

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 18 ⎯z Status CommandsTable 3 lists the status commands that set and query the variousregisters and queues th

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 20 ⎯*WAI Wait to continue. This command forcessequential operation of commands. Thiscommand is required by IE

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 22 ⎯Examples:*ESE 65 sets the ESER to binary 0100 0001.If the ESER contains the binary value 1000 0010, the *

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 24 ⎯*SRE?Returns:<NR1> is in the range from 0 through 255.Examples*SRE 7 sets bits of the SRER to 0000

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 26 ⎯Returns:0/1Examples::CONFigure:AUTo 1Set to auto-range mode.If it is in the auto-range mode, the command

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 28 ⎯:CONFigure:TEMPerature(no query form)Function:Set the temperature functionSyntax::CONFigure:TEMPeratureEx

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 30 ⎯Examples::CONFigure:TCOMpensate:TEMPerature 20 sets require temperature to20.0℃.:CONFigure: TCOMpensate:T

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 32 ⎯Examples::CONFigure: :SCAN:CHANnel 8 sets the channel of scan.:CONFigure:SCAN:CHANnel? Return 8 to indica

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 34 ⎯:READ?(query only)Function:Returns the measurement value with 14 characters totally.Syntax::READ?Return:

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 36 ⎯:CALCulation:LIMit:LOWerFunction:Returns or sets the value of the lower limit in the compare mode.Syntax:

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 2 ⎯2. CONNECTING THE METER VIA GPIB INTERFACEThe GPIB interface capabilities:The GPIB interface of the Meter

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 38 ⎯:CALCulation:LIMit:NORMal <NR1>Examples::CALCulation:LIMit:NORMal? might return 10000 in the COMP m

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 40 ⎯STATus:OPERation:CONDition? (query only)Function:Return the contents of the OPERation register. The METER

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 42 ⎯Returns:<NR1>Examples:STATus:QUEStionable:CONDition? returns 0.STATus:QUEStionable:ENABleFunction:S

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 44 ⎯SYSTem:ERRor? returns 0, “No error”SYSTem:VERSion? (query only)Function:Return the SCPI version of the de

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 46 ⎯Temperature OverloadNot UsedNot UsedLimit Test Fail HILimit Test Fail LO Not UsedOhm

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 48 ⎯Table 4: QUEStionable Status RegisterBit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8∗NU NU Limit Te

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 50 ⎯Use the serial poll or the *STB? Query to read the contents of the SBR.The bits in the SBR are set and cl

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 52 ⎯QueuesThe output queue is included to power supplies.Output Queue: The METER store query responses in the

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 4 ⎯The GPIB connection testingIf you want to test whether the GPIB connection is working or not, youcan send

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 6 ⎯z Ensure the same baud rate is used on the device as the one used onPC terminal.z Ensure the connector f

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 8 ⎯The RS232 connection testingIf you want to test whether the RS232 connection is working or not, youcan sen

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 10 ⎯command identifies it as a query.Layer D is interrelated with device information. Different devices haved

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 12 ⎯Table 1 defines the Boolean and other parameter types for the Meter.Parameter Type Description ExampleBoo

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 14 ⎯Combining CommandsYou can use a semicolon (;) to combine commands. But continuouslyquery command will cau

DC MILLI-OHM METERPROGRAMMER MANUAL⎯ 16 ⎯:CONFigure:SCAN:STATe<Boolean> Sets scan mode on or off.:CONFigure:SCAN:STATe? Returns scan mode on