Gw-instek PSW-Series Programming & Command manual Uživatelský manuál Strana 6
- Strana / 118
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
PSW Series Programming Manual
6
Cleaning the PSW
Disconnect the power cord before cleaning.
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
Do not use chemicals containing harsh material
such as benzene, toluene, xylene, and acetone.
Operation
Environment
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
Relative Humidity: 20%~ 85%
Altitude: < 2000m
Temperature: 0°C to 50°C
(Pollution Degree) EN61010-1:2010 and EN61010-2-030 specify the
pollution degrees and their requirements as follows. The PSW falls
under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Storage
environment
Location: Indoor
Temperature: -25°C to 70°C
Relative Humidity: <90%
Disposal
Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.
- Multi-Range DC Power Supply 1
- Table of Contents 3
- SAFETY INSTRUCTIONS 4
- Safety Guidelines 5
- GETTING STARTED 8
- PSW Series Overview 9
- Main Features 10
- Accessories 11
- PSW 250/800 Accessories 12
- Appearance 14
- Function 15
- Lock/Local 15
- AC Input 17
- 100 240V 18
- 47 63Hz 500VA MAX 18
- V SN.C. S V 18
- Configuration Table 24
- M, N = USB Driver version 27
- REMOTE CONTROL 29
- Interface Configuration 30
- Configure GPIB Interface 31
- Web Server Configuration 32
- Sockets Server Configuration 33
- Socket Server Function Check 39
- Socket Server Examples 45
- C++ Example 46
- REMOTE CONTROL 47
- LabVIEW Example 48
- Command Syntax 49
- 1 2 3 4 5 51
- Command List 52
- Abort Commands 55
- APPLy Commands 55
- DISPlay[:WINDow]:TEXT:CLEar 57
- DISPlay[:WINDow]:TEXT[:DATA] 57
- DISPlay:BLINk 57
- Initiate Commands 58
- INITiate[:IMMediate]:NAME 58
- Returns the current in amps 59
- OUTPut:MODE 61
- OUTPut[:STATe][:IMMediate] 61
- OUTPut[:STATe]:TRIGgered 61
- OUTPut:PROTection:CLEar 62
- OUTPut:PROTection:TRIPped 62
- Sense Commands 63
- SENSe:AVERage:COUNt 63
- Event register 64
- Condition register 64
- STATus:OPERation:PTRansition 65
- STATus:OPERation:NTRansition 65
- STATus:QUEStionable[:EVENt] 65
- STATus:QUEStionable:ENABle 66
- STATus:PRESet 67
- Source Commands 68
- [:AMPLitude] 68
- [SOURce:]CURRent:SLEW:RISing 70
- [SOURce:]VOLTage:SLEW:RISing 73
- TRIGger:OUTPut[:IMMediate] 76
- TRIGger:OUTPut:SOURce 76
- Trigger Command Examples 76
- SYSTem:BEEPer[:IMMediate] 79
- SYSTem:CONFigure:MSLave 82
- [:MODE] 82
- SYSTem:COMMunicate:ENABle 83
- SYSTem:COMMunicate:LAN:SMASk 85
- SYSTem:COMMunicate:LAN:MAC 85
- SYSTem:COMMunicate:LAN:DHCP 85
- SYSTem:COMMunicate:LAN:DNS 86
- SYSTem:ERRor 88
- SYSTem:KEYLock:MODE 88
- SYSTem:KLOCk 88
- SYSTem:INFormation 89
- SYSTem:PRESet 89
- SYSTem:VERSion 89
- IEEE 488.2 Common Commands 90
- Status Register Overview 94
- The Status Registers 95
- Error Que 103
- Error List 105
- Execution Errors 109
- Device Specific Errors 111
- Query Errors 112
- APPENDIX 114
- LED Display Format 117
Související produkty a manuály pro Zařízení Gw-instek PSW-Series Programming & Command manual
Zařízení Gw-instek PCS-1000 Uživatelský manuál
(93 stránky)
(93 stránky)
Zařízení Gw-instek GPD-4303S Uživatelský manuál
(59 stránky)
(59 stránky)
Zařízení Gw-instek PPH-1503 Uživatelský manuál
(137 stránky)
(137 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce